After the broadband upgrade to 100M, the hundred-dollar routers apparently ran understeer. Obsessive-compulsive disorder was very unpleasant. After researching the major forums, the new Asus AC66U B1 was found to be appropriate and has the following advantages:
1. Asus quality, strong stone
2. ASUS firmware, direct upgrade Merlin firmware is simple
3. After brushing Merlin performance with AC68U, the price is in the 500-600 position
4. Gigabit ports, dual-core 1Ghz, extended rich (I mainly like to advertise)
5. Compared with the pre-made AC66U, not only the performance improvement, USB3.0 interface pre-address signal interference
Appearance Gallery
1 The above picture shows that the appearance of AC66U B1 is very texture, there is a large area of ​​heat sink inside, normal use of the CPU is about 70 °.
2 AC66U B1 can directly upgrade Merlin firmware in settings, release performance, and install plug-ins. Specific brush firmware tutorial can look at the value of the Friends of the article.
ASUS RT-AC66U B1 wireless router out of the box evaluation! Hello, everyone, we have come again! This time to share with everyone is the ASUS router AC66UB1, note that there is a B1 Oh! ! ! This is the following goods: ASUS RT-AC66UB1AC dual-frequency 1750M low-radiation 1GHz dual-core processor USB3.0 three-antenna wide coverage smart router Asus (ASUS) RT-AC66UB1AC dual-frequency 1750M low-emission 1G... wolf story | Like 109 Comments 196 Favorites 837 View Details 3 After you finish the Merlin firmware, you can see the CPU's real-time information and temperature in the lower right corner of the main interface.
4 After you finish Merlin firmware, you can see the plug-in center at the bottom of the main menu. The advertisement plug-in can be directly installed and opened. Youku, Tudou, Sohu, Iqiyi and other websites instantly have no advertisement. Tencent video uses the https rule and needs Follow the plug-in prompts to set up to do advertising (this feature is critical). Of course, you can play the value of friends can plug-in center to find a variety of functional plug-ins.
After brushing the firmware and looking at the 70° router, I usually feel that the router is hot. The first time I found the temperature was so high (OCD is not calm). Looking for solutions on the Internet, we found that there are basically three options:
1 open cover type
2 external fan type
3 under the notebook cooling fan
It seems that the above scenario first destroys the appearance of the router, and the second affects the appearance of the router. The third type of notebook heatsink takes up too much space on the desktop.
Plan determination The initial development plan determines three general requirements: 1 The operation is simple and the accessories are cheap. 2 does not destroy the overall excuse of the router does not affect the appearance of the router. 3 The heat sink has a simple structure and a small footprint. 4 quiet, long service life.
Looking for the little things in the family, I found a feasible solution as follows:
1 hard small cardboard box, I chose a wiring board packaging
2 USB electronic product charge line
3 12CM chassis fan one, I chose Qiao Sibo chassis fan, noise control is very good, mainly one year warranty, the same price of other brands of fans is not a month warranty or three months (elimination)
JONSBO 12020 12CM chassis fan (20MM thin thickness / motherboard 3PI interface + power D port interface / mute) 19.9 yuan Jingdong direct link 
1 The cartons have been folded perfectly, only need to remove the cover and can be used directly, of course, also need to dig two vent holes in the 2 side so that the air flow can effectively cycle, of course, for the sake of beauty, it is recommended to use a ruler to design a good, and then Form a knife with a sharp blade.
2 Connect the USB cable and chassis fan, remove the end of the USB cable, expose the 4 cable ends, find a red line and a black cable, the other 2 cuts are not used, and the chassis fan has a 3PIN excuse and a 4PIN excuse. It can be seen that there are exactly 2 holes in the 4PIN connection to the red and black lines of the USB.
3 The red and black lines are respectively inserted into the 2 holes of the 4PIN interface, and taped and fixed.
4 Attach the attached fan to the paper tray. The fan has 4 screws for just use. This step mainly pays attention to the fan's wind direction. My own installation is to inhale from the router. After installation, the temperature drops from 70 directly to 50. Another method of blowing may be reduced to a lower level, but there may be more dust entering the router. You value your friends to weigh the pros and cons.
5 After all the installation is complete, put the router on the paper tray, and pull the USB head out of the rear vent into the USB 2.0 port on the back of the router. Normal operation will take place and the temperature of the router will fall.
Last molding
Router: 1 AC66U B1 has strong performance, and TV, PAD, mobile phone, and computer have multiple client access stability.
2 Extensive performance, easy brushing, and practicality of plug-ins available.
3 1900M bandwidth, Gigabit ports meet daily needs.
Self-made cooling base: 1 router dismantling, plug in first, easy to make.
2 The low cost requires only a 19.9 chassis fan (JD East warranty for one year), a discarded USB charging cable, and a discarded cardboard box.
3 The battle area is small, quiet and low power consumption. After being idle, the chassis fans can be used without damage.
Although the performance of the AC66U B1 is similar to that of the AC68U, I heard that some aspects of the AC66U and the AC68U have shrunk compared to the AC65U. Finally, of course, it is hoped that the price will be able to do more with the people, and the heat dissipation performance will be stronger. Of course, AC66U B1 can still meet the needs of ordinary families at this stage and it is worth recommending.
Mono Solar Panel,Poly Solar Panel,HJT, BIPV, Double Glass,Small Solar Panel,Solar Cell Panel
Wuxi Sunket New Energy Technology Co.,Ltd , https://www.sunketsolar.com